Pro-tools 105B Bedienungsanleitung Seite 1

105-B BENDERINSTRUCTION SET“THE BRUTE”PRO-TOOLS7616 INDUSTRIAL LANE TAMPA, FLORIDA 33637-6715813-986-9000 PHONE 813-985-6588 FAXwww.pro-tools.co

105-SB BENDER-DIE INSTALL-813-986-9000PAGE 10PRO-TOOLSQUICK RELEASE NOTESTHE TENSION BOLT SERVERS TWO PURPOSES:1) IN MOST CASES IT IS NECESSARY TO KEE

105-SB BENDER-IMPORTANT-813-986-9000PAGE 11PRO-TOOLSRADIUS OF MAIN DIE MUST BE CLEAN. ABSOLUTELY NO GREASE!TIGHTEN TENSION BOLT SO TUBEWILL NOT SLIP.

105-SB BENDER-BENDING INSTRUCTIONS-813-986-9000PAGE 12PRO-TOOLSFIG. ASTARTING POSITIONFIG. BSTEP 1 - EXTEND CYLINDER TO A FULL STROKESTEP 2 - SNUG BOL

105-SB BENDER-BENDING INSTRUCTIONS-813-986-9000PAGE 13PRO-TOOLSFIG. CFIG. DINSTALL SWING ARM PIN IN NEW HOLE IN DIE & RUN THROUGH STROKE AGAIN.REP

PAGE 14QUALITY PRODUCTS BY PEOPLE WHO CARE (813) 986-9000BENDING INSTRUCTIONSIN THE NEXT FEW PAGES, WE ARE GOING TO EXPLAIN A FEW THINGS ABOUT BENDERS

PAGE 15QUALITY PRODUCTS BY PEOPLE WHO CARE (813) 986-9000BENDING INSTRUCTIONS12”24”36”1 ½”STEP 2TAKE THE 36” LONG PIECE OF TUBING AND MEASURE EXACTLY

PAGE 16QUALITY PRODUCTS BY PEOPLE WHO CARE (813) 986-9000BENDING INSTRUCTIONSSTEP 4WE ARE NOW READY TO START A BENDING PROJECT. IN OUR EXAMPLE WE WILL

PAGE 17QUALITY PRODUCTS BY PEOPLE WHO CARE (813) 986-9000BENDING INSTRUCTIONSSTEP 6INSTALL TUBING IN BENDER AS SHOWN AND COMPLETE THE LAST BEND.AT THI

PAGE 18QUALITY PRODUCTS BY PEOPLE WHO CARE (813) 986-9000HELPFUL INFORMATIONTO MEASURE RADIUS:START AT IMAGINARY CENTEROF SLEEVE, MEASURE TO EDGEOF DI

FAQ’sQ: WHAT SIZE MATERIAL CAN I BEND WITH THE BRUTE?A: UP TO 2 ½”x .134 WALL STEEL TUBE AND 2” SCHEDULE 40 PIPE.Q: THE TUBE IS STUCK IN THE BENDER?A:

105-SB BENDERWARRANTY POLICYALL PRODUCTS PRO-TOOLS MANUFACTURES CARRY A ONE YEARGUARANTEE AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP. (PRODUCTSTHAT WE

105-SB BENDER-CONTENTS-813-986-9000PAGE 3PRO-TOOLSWHEN YOU RECEIVE YOUR MB-105-SB “BRUTE” BENDER, YOU WILL HAVE3 PACKAGES.1) MB-105-SB BENDER2) HYDRAU

105-SB BENDER-STAND SETUP-813-986-9000PAGE 4PRO-TOOLSSTEP 1BOLT STAND TO FLOORSTEP 2SET BENDER ON STAND& TIGHTEN BOLTS.STEP 3MAKE SURE ONE INCH PI

105-SB BENDER-HYDRAULIC SETUP-813-986-9000PAGE 5PRO-TOOLSCYLINDER CONNECTORSCREW CYLINDER INTO BRACKET ( MAKE SURE IT IS TIGHTOR IT WILL DAMAGE THE TH

105-SB BENDER-DIE INSTALL813-986-9000PAGE 6PRO-TOOLSDIE PIVOT PINDIE DRIVE PINMAIN DIE INSTALLREMOVE 1” DIE PIVOT PIN, LUBRICATE PIN AND DIE SLEEVE, P

105-SB BENDER-DIE INSTALL813-986-9000PAGE 7PRO-TOOLSQUICK RELEASE INSTALLINSERT BACKING BLOCK INTO QUICK RELEASE & INSTALL PIN AS SHOWNTO HOLD BLO

105-SB BENDER-DIE INSTALL813-986-9000PAGE 8PRO-TOOLSTUBE & BACKING BLOCK INSTALLBENDER SWINGARMS MUST BE CLOSED AGAINST BENDER FRAME BEFOREINSTALL

105-SB BENDER-DIE INSTALL813-986-9000PAGE 9PRO-TOOLSSTRAP & PIN INSTALLPUSH FIRMLY ON END OF TUBE, PLACE STRAP AROUND TUBE, LINE UPHOLES, THEN INS